This is my Track car. I use it mostly for HPDE's and light autocross.

The car makes 349HP 321TQ @ 19PSI (wastegate) with 91 octane tune by Modified by KC on the Dyno. I wanted a safe mild tune for me to learn the car on track with. Plenty more power available with some more boost. May get the car re-tuned late August for some more power at 23/24PSI. I am finally getting use to it and now may actually be able to use that extra power. As is it's a blast on track and can pretty much take on anything. I just need to become a better driver.

The car weights 2912 with 1/2 tank gas. (Scaled at SCCA Pro Solo)

Here's the Mod list:

Engine/Drivetrain:

- Full-race pro-street manifold HPC coated with EGT sensor on #2 runner
- FP Green port fully matched
- FP High performance wastegate actuator
- FP 2” SS outlet pipe (custom cut to work with ETS LICP)
- FP stainless 02 housing
- Greddy Racing Titanim cat-back exhaust (11 pounds)
- DC sports 3” Stainless downpipe (with catalytic convertor elimination). Downpipe tapped for wideband and DEI exhaust wrap.
- ETS 3.5” custom FMIC designed to fit Cusco power brace
- ETS 2.5” ultra-short route FMIC piping (silver powdercoat)
- ETS 3” intake and filter adapter (silver powdercoat)
- ETS mini-battery kit with battery (silver powdercoat)
- MIL.SPEC ported Intake Manifold with custom NPT bungs for Zeitronix MAP sensor, AEM boost gauge and BOV pressure sources
- MIL.SPEC 65mm ported/polished throttle body with re-built seals
- Zaklee clear cam cover
- Ralliart plug wires
- Ralliart Thermostat
- Ralliart High Pressure Radiator Cap
- Tomei Thermostat killer
- Fluidyne 7” puller fan installed on oil-cooler
- AC removed and Evo VIII RS AC eliminator serpentine belt installed
- Heater core blocked off.
- XS Engineering Racemax 272 cams
- XS Engineering Ignition Amplifier
- Crower dual Titanium Valve springs and Retainers
- Exedy Clutch
- AMS full length stainless clutch line
- Aeromotive fuel rail
- FIC 750cc injectors
- Saikou Michi DC3 Split catch cans (black)
- PCV valve elimination
- Mishimoto slim radiator with custom 13” puller fan and brackets
- Gates high-performance radiator hoses
- Perma-cool 13” pusher fan mounted in condenser fan location for extra cooling
- Powerflex solid side motor mounts
- AMS chromoly lower engine brace with solid bottom motor mount
- AMS Moustache brace eliminator and solid rear diff bushings
- TRE Ralliart LSD and T-case re-built by Jon Ripple
- TRE Rear differential upgrade (1 way clutch pack) and re-build by Jon Ripple
- Beatrush solid driveshaft bushings
- Beatrush radiator cooling panel
- Perrin Short Shifter
- Billet shifter base bushings
- Billet shifter cable bushings

Suspension:

- Whiteline 24mm rear swaybar
- Whiteline 25mm front swaybar
- Whiteline performance front swaybar endlinks
- Whiteline performance rear swaybar endlinks
- Whiteline precision-steer kit
- Whiteline roll-center correction kit
- Whiteline front LCA bushing
- Whiteline rear LCA bushing
- Whiteline rear lower strut mount bushing
- Whiteline rear trailing arm bushing
- Whiteline rear toe arm bump steer kit
- Perrin Performance rear swaybar stout mounts kit
- Perrin Performance PRSR kit with offset caster bushing
- GT-Spec rear trunk cage
- GT-Spec 5 point lower ladder brace
- Beatrush front LCA braces
- Megan Track coilovers
- Cusco power front brace
- APR flex-control upper strut brace


Exterior:

- Chargespeed D1 20mm widebody FRP fenders (modified to shave blinker hole)
- APR front carbon fiber splitter
- APR carbon fiber dual canard setup
- Seibon Carbon Fiber trunk lid (keyhole painted black)
- Seibon Carbon fiber hood (OEM style modified by painting mesh black)
- APR GTC-200 Carbon fiber rear spoiler
- APR carbon fiber rear diffuser
- APR Carbon Fiber formula GT mirrors
- Custom aluminum sunroof block-off plate (paint matched)
- Rexpeed black vortex generator
- Rexpeed Carbon Fiber cooling ducts

Wheels/tires/brakes:

- Rota 18x9.5 P45R with 285/30/18 Hoosier R6s
- Dunlop NON-D.O.T Race Slicks to replace the R6s when they are shot
- Konig 18x9 Runaway Shadow Black with 275/35/18 NT01's
- H&R 25mm wheel spacers
- Ichiba 10mm wheel spacers
- Hawk HP+ front and rear brake pads (AutoX)
- HT-10 Bads front and rear (Road Course)
- ATE Blue in the reservoir.
- Teflon coated SS brake lines
- Hotlap Motorsports brake cooling ducts

Interior/Electronics:

- Autopower 4 point rollbar with diagonal brace and driver’s side rear brace
- Beatrush performance floor brace
- Sparco 5 point SFI/FIA certified harnesses
- Works Bell Slim steering hub adaptor
- NRG 350mm deep corn style black leather steering wheel
- Corbeau FXPro racing seats
- AEM truboost boost controller/gauge mounted on Autometer Steering pod gauge panel
- AEM Coolant temp, AEM oil temp and AEM oil pressure gauges mounted on Gruppe-S triple gauge pod
- Raptor performance shift-light custom installed on instrument panel garnish
- Zeitronix wideband display custom installed in clock location using S-AFC bracket.
- Zietronix ZAVT-1 custom installed in dash
- Zietronix ZT2 brain unit (boost and EGT options) installed in glovebox
- All door panels, seats, carpet, OEM seat belts, all plastic trim, unnecessary brackets removed to reduce weight
- All sound deadening removed including dash mat insulation behind dash
- Interior wiring harness was de-pinned to eliminate any unnecessary wiring (stereo, ETACS, power windows/locks, sunroof, SRS etc). Over 13 lbs of harness was removed.
- Full manual windows and door lock conversion from Evo VIII RS installed. Door panels will not installed to keep weight down
- Beatrush bulkhead division plate